Came BX-78 Kit Manuel d'utilisateur

BX SERIESINSTALLATION MANUAL BX-74 / BX-78AUTOMATION SYSTEMS FOR SLIDING GATESEnglishEN

6.1 General description 6 Control boardFUSE TABLE To protect: fuse:Control board (line) 5A-FAccessories 1A-FCommand devices 630mA-FTECHNICAL INFORMATI

6.3 Electrical connectionsTerminals for powering the following accessories: - 24V A.C. Maximum allowed power: 35WPower supply for accessories+-COMNCNC

Cycle lamp: (contact rating: 230V – 60W max.).It lights up the driving area and stays on from the moment the gate begins to open until it is fully clo

«partial stop» (N.C.) contact - Input for EN 12978 standard-compliant safety devices such as photocells. Gate stops if moving and automatically shuts

DIP-SWITCH 10 1 ON - Automatic Closing - The automatic closing timer activates at the end of the opening gate run. The pre-set time is adjustable, an

6.6 Programming decelerationsSo as to fully meet the compliance requirements established by European Standards EN 12445 and EN 12453 on matters concer

7 Activating the radio command• •••••••1234ON56789101234ON6.8 Motor torque limiterTo vary the motor torque, move the shown faston (the one with the bl

••••••••••••••••1234ON56789101234ONTransmittersInsert the radio frequency card into the electronic card AFTER DISCONNECTING THE POWER (and disconnecti

••••••••••••••••AF1234ON56789101234ON••••••••••••••••AF1234ON56789101234ONLED on- Repeat the procedure for the “CH2” button associating this to anothe

A1) Coordinate the direction of travel of geared motors “A” and “B”, by modifying the rotation of motor “B” (see p. 11 geared motor-endstop connection

4.1 OperatorThis product is engineered and manufactured by CAME CANCELLI AUTOMATICI S.p.A. in compliance with current safety standards. Guaranteed 24

9 Safety instructionsThis product must only be employed for its originally intended use. Any other use is wrong and potentially dangerous. The manuf

10 Maintenance10.1 Periodic maintenance Periodic maintenance to be carried out by the end-user is as follows: wipe clean the glass surface of the pho

10.3 Extra-ordinary maintenance The following table serves to note down any extraordinary maintenance, repairs or improvements performed by specia-li

11 Phasing out and disposal CAME Cancelli Automatici S.p.A. via Martiri della Libertà, 15 31030 Dosson di Casier - Treviso - ITALY tel (+39) 0422

CAME France S.a.CAME France S.a.7, Rue Des HarasZ.i. Des Hautes Patures92737 Nanterre Cedex - Nanterre Cedex - FRANCE (+33) 1 46 13 05 05 (+33) 1 46 1

4.4 Dimensions4.3 Description of parts(mm)5 Installation Installation must be carried out by expert qualified personnel and in full compliance

Make sure you have all the tools and materials you will need for the installation at hand to work in total safety and compliance with the current sta

- Dig a pit to the side of the gate (see measurements from diagram). Prepare the corrugated tubes you will need when making connections coming from th

H- To position the plate in relation to the rack please see the measurements on the diagram.Fill the form box with cement and wait for at least 24 h

- Remove the cover from the gearmotor by loosening the side bolts, perforate the cable shafts using a screwdriver or a pair of scissors and

- Open and close the gate manually and register the pinion-to-rack distance using the threaded steel-levelling feet (for vertical adjusting)

5.7 Manually releasing the gearmotor- Insert the trilobed key into the lock, push it in and turn it clockwise ...5.6 Mounting the endstop fin